boards/esp32s3: add support to esp32s3-lhcbit board
The esp32s3-lhcbit is a board with lora, sdcard, display TFT, etc. Signed-off-by: Jorge Guzman jorge.gzm@gmail.com
This commit is contained in:
Jorge Guzman
Xiang Xiao
parent
8723aa7125
commit
e3dabcd999
15 changed files with 944 additions and 0 deletions
|
|
@ -0,0 +1,113 @@
|
|||
=================
|
||||
esp32s3-lhcbit
|
||||
=================
|
||||
|
||||
This page discusses issues unique to NuttX configurations for the
|
||||
ESP32S3-LHCBit board.
|
||||
|
||||
.. figure:: lcb-bit-top.jpeg
|
||||
:align: center
|
||||
|
||||
.. figure:: lcb-bit-botton.jpeg
|
||||
:align: center
|
||||
|
||||
Board information
|
||||
=================
|
||||
|
||||
This board was release by Laboratório Hacker de Campinas (LHC) in 2024 and developed based on
|
||||
ESP32-S3-WROOM-1 module.
|
||||
|
||||
The board features:
|
||||
- ESP32-S3-16R8
|
||||
- USB-to-UART bridge via micro USB port
|
||||
- SPI FLASH (size varies according to model)
|
||||
- Lora module RAK3172-SiP
|
||||
- Adafruit Mini TFT - 0.96" 160x80
|
||||
|
||||
Board documentation: https://github.com/lhc/Hardware/tree/main/LHCbit
|
||||
|
||||
BOARD-RGB LED
|
||||
==============
|
||||
|
||||
The LHCBit board has one LED RGB Addressable
|
||||
|
||||
======= =====
|
||||
LED PINS
|
||||
======= =====
|
||||
LED_RGB IO14
|
||||
======= =====
|
||||
|
||||
BOARD BUTTONS
|
||||
==============
|
||||
|
||||
The LHCBit board has 2 buttons
|
||||
|
||||
======= =====
|
||||
BUTTON PINS
|
||||
======= =====
|
||||
SW1 IO13
|
||||
SW2 IO12
|
||||
======= =====
|
||||
|
||||
BOARD LORA
|
||||
==========
|
||||
|
||||
The LHCBit board has a RAK3172-SiP lora module with AT command communication via UART
|
||||
|
||||
========= =====
|
||||
LORA PINS
|
||||
========= =====
|
||||
UART1_TX IO9
|
||||
UART1_RX IO11
|
||||
BOOT IO10
|
||||
========= =====
|
||||
|
||||
BOARD DISPLAY
|
||||
===============
|
||||
|
||||
The LHCBit board comes with a 0.96" TFT display with sdcard, both with SPI communication and individual CS pins.
|
||||
|
||||
========= =====
|
||||
SHIELD PINS
|
||||
========= =====
|
||||
SPI_MOSI IO15
|
||||
SPI_MISO IO16
|
||||
TFT_CS IO21
|
||||
TFT_RESET IO48
|
||||
TFT_DC IO37
|
||||
SD_CS IO39
|
||||
========= =====
|
||||
|
||||
Configurations
|
||||
==============
|
||||
|
||||
All of the configurations presented below can be tested by running the following commands::
|
||||
|
||||
tools/configure.sh esp32s3-lhcbit:<subdir>
|
||||
|
||||
Where <subdir> is one of the following:
|
||||
|
||||
Configuration Directories
|
||||
-------------------------
|
||||
|
||||
usbnsh
|
||||
------
|
||||
|
||||
Configures the NuttShell (nsh) located at apps/examples/nsh. This configuration enables a serial console over USB.
|
||||
|
||||
After flasing and reboot your board you should see in your dmesg logs::
|
||||
|
||||
$ sudo dmesg | tail
|
||||
[ 3315.687219] usb 3-1.1.1: new full-speed USB device number 10 using xhci_hcd
|
||||
[ 3315.778666] usb 3-1.1.1: New USB device found, idVendor=0525, idProduct=a4a7, bcdDevice= 1.01
|
||||
[ 3315.778684] usb 3-1.1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
|
||||
[ 3315.778689] usb 3-1.1.1: Product: CDC/ACM Serial
|
||||
[ 3315.778694] usb 3-1.1.1: Manufacturer: NuttX
|
||||
[ 3315.778697] usb 3-1.1.1: SerialNumber: 0
|
||||
[ 3315.829695] cdc_acm 3-1.1.1:1.0: ttyACM0: USB ACM device
|
||||
[ 3315.829725] usbcore: registered new interface driver cdc_acm
|
||||
[ 3315.829727] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
|
||||
|
||||
|
||||
You may need to press ENTER 3 times before the NSH show up.
|
||||
|
||||
Binary file not shown.
|
After Width: | Height: | Size: 548 KiB |
Binary file not shown.
|
After Width: | Height: | Size: 441 KiB |
|
|
@ -463,6 +463,14 @@ config ARCH_BOARD_ESP32S3_LCD_EV
|
|||
1. ESP32-S3-LCD-EV-Board with 480x480 LCD
|
||||
2. ESP32-S3-LCD-EV-Board with 800x480 LCD
|
||||
|
||||
config ARCH_BOARD_ESP32S3_LHCBIT
|
||||
bool "ESP32-S3 LHCBit"
|
||||
depends on ARCH_CHIP_ESP32S3WROOM1N16R8
|
||||
select ARCH_HAVE_BUTTONS
|
||||
select ARCH_HAVE_IRQBUTTONS if ESP32S3_GPIO_IRQ
|
||||
---help---
|
||||
The ESP32-S3 LHCBit features the ESP32-S3 CPU with dual Xtensa LX7 cores.
|
||||
|
||||
config ARCH_BOARD_ESP32S3_BOX
|
||||
bool "Espressif ESP32-S3-BOX"
|
||||
depends on ARCH_CHIP_ESP32S3WROOM2N16R8V || ARCH_CHIP_ESP32S3WROOM2N32R8V || ARCH_CHIP_ESP32S3CUSTOM
|
||||
|
|
@ -3257,6 +3265,7 @@ config ARCH_BOARD
|
|||
default "esp32s3-eye" if ARCH_BOARD_ESP32S3_EYE
|
||||
default "esp32s3-meadow" if ARCH_BOARD_ESP32S3_MEADOW
|
||||
default "esp32s3-lcd-ev" if ARCH_BOARD_ESP32S3_LCD_EV
|
||||
default "esp32s3-lhcbit" if ARCH_BOARD_ESP32S3_LHCBIT
|
||||
default "esp32s3-box" if ARCH_BOARD_ESP32S3_BOX
|
||||
default "esp32s3-korvo-2" if ARCH_BOARD_ESP32S3_KORVO_2
|
||||
default "esp32c6-devkitc" if ARCH_BOARD_ESP32C6_DEVKITC
|
||||
|
|
@ -4407,6 +4416,9 @@ endif
|
|||
if ARCH_BOARD_ESP32S3_LCD_EV
|
||||
source "boards/xtensa/esp32s3/esp32s3-lcd-ev/Kconfig"
|
||||
endif
|
||||
if ARCH_BOARD_ESP32S3_LHCBIT
|
||||
source "boards/xtensa/esp32s3/esp32s3-lhcbit/Kconfig"
|
||||
endif
|
||||
if ARCH_BOARD_ESP32S3_BOX
|
||||
source "boards/xtensa/esp32s3/esp32s3-box/Kconfig"
|
||||
endif
|
||||
|
|
|
|||
84
boards/xtensa/esp32s3/esp32s3-lhcbit/Kconfig
Normal file
84
boards/xtensa/esp32s3/esp32s3-lhcbit/Kconfig
Normal file
|
|
@ -0,0 +1,84 @@
|
|||
#
|
||||
# For a description of the syntax of this configuration file,
|
||||
# see the file kconfig-language.txt in the NuttX tools repository.
|
||||
#
|
||||
|
||||
if ARCH_BOARD_ESP32S3_LHCBIT
|
||||
|
||||
config ESP32S3_STORAGE_MTD_OFFSET
|
||||
hex "Storage MTD base address in SPI Flash"
|
||||
default 0x180000 if !ESP32S3_HAVE_OTA_PARTITION
|
||||
default 0x250000 if ESP32S3_HAVE_OTA_PARTITION
|
||||
depends on ESP32S3_MTD
|
||||
---help---
|
||||
MTD base address in SPI Flash.
|
||||
|
||||
config ESP32S3_STORAGE_MTD_SIZE
|
||||
hex "Storage MTD size in SPI Flash"
|
||||
default 0x100000
|
||||
range 0x0 0x400000 if ESP32S3_FLASH_4M
|
||||
range 0x0 0x800000 if ESP32S3_FLASH_8M
|
||||
range 0x0 0x1000000 if ESP32S3_FLASH_16M
|
||||
range 0x0 0x2000000 if ESP32S3_FLASH_32M
|
||||
depends on ESP32S3_MTD
|
||||
---help---
|
||||
MTD size in SPI Flash.
|
||||
|
||||
choice ESP32S3_SPIFLASH_FS
|
||||
prompt "Mount SPI Flash MTD on bring-up"
|
||||
default ESP32S3_SPIFLASH_SMARTFS
|
||||
depends on ESP32S3_MTD
|
||||
optional
|
||||
---help---
|
||||
Mount the SPI Flash MTD with the selected File System format on board
|
||||
bring-up.
|
||||
If not selected, the MTD will be registered as a device node on /dev.
|
||||
|
||||
config ESP32S3_SPIFLASH_SMARTFS
|
||||
bool "SmartFS"
|
||||
select FS_SMARTFS
|
||||
select MTD_SMART
|
||||
|
||||
config ESP32S3_SPIFLASH_NXFFS
|
||||
bool "NXFFS"
|
||||
select FS_NXFFS
|
||||
|
||||
config ESP32S3_SPIFLASH_SPIFFS
|
||||
bool "SPIFFS"
|
||||
select FS_SPIFFS
|
||||
|
||||
config ESP32S3_SPIFLASH_LITTLEFS
|
||||
bool "LittleFS"
|
||||
select FS_LITTLEFS
|
||||
|
||||
endchoice # ESP32S3_SPIFLASH_FS
|
||||
|
||||
if PM
|
||||
|
||||
config PM_ALARM_SEC
|
||||
int "PM_STANDBY delay (seconds)"
|
||||
default 15
|
||||
---help---
|
||||
Number of seconds to wait in PM_STANDBY before going to PM_STANDBY mode.
|
||||
|
||||
config PM_ALARM_NSEC
|
||||
int "PM_STANDBY delay (nanoseconds)"
|
||||
default 0
|
||||
---help---
|
||||
Number of additional nanoseconds to wait in PM_STANDBY before going to PM_STANDBY mode.
|
||||
|
||||
config PM_SLEEP_WAKEUP_SEC
|
||||
int "PM_SLEEP delay (seconds)"
|
||||
default 20
|
||||
---help---
|
||||
Number of seconds to wait in PM_SLEEP.
|
||||
|
||||
config PM_SLEEP_WAKEUP_NSEC
|
||||
int "PM_SLEEP delay (nanoseconds)"
|
||||
default 0
|
||||
---help---
|
||||
Number of additional nanoseconds to wait in PM_SLEEP.
|
||||
|
||||
endif # PM
|
||||
|
||||
endif # ARCH_BOARD_ESP32S3_LHCBIT
|
||||
|
|
@ -0,0 +1,50 @@
|
|||
#
|
||||
# This file is autogenerated: PLEASE DO NOT EDIT IT.
|
||||
#
|
||||
# You can use "make menuconfig" to make any modifications to the installed .config file.
|
||||
# You can then do "make savedefconfig" to generate a new defconfig file that includes your
|
||||
# modifications.
|
||||
#
|
||||
# CONFIG_NSH_ARGCAT is not set
|
||||
# CONFIG_NSH_CMDOPT_HEXDUMP is not set
|
||||
CONFIG_ARCH="xtensa"
|
||||
CONFIG_ARCH_BOARD="esp32s3-lhcbit"
|
||||
CONFIG_ARCH_BOARD_COMMON=y
|
||||
CONFIG_ARCH_BOARD_ESP32S3_LHCBIT=y
|
||||
CONFIG_ARCH_CHIP="esp32s3"
|
||||
CONFIG_ARCH_CHIP_ESP32S3=y
|
||||
CONFIG_ARCH_CHIP_ESP32S3WROOM1N16R8=y
|
||||
CONFIG_ARCH_INTERRUPTSTACK=2048
|
||||
CONFIG_ARCH_STACKDUMP=y
|
||||
CONFIG_ARCH_XTENSA=y
|
||||
CONFIG_BOARDCTL_USBDEVCTRL=y
|
||||
CONFIG_BOARD_LOOPSPERMSEC=16717
|
||||
CONFIG_BUILTIN=y
|
||||
CONFIG_CDCACM=y
|
||||
CONFIG_CDCACM_CONSOLE=y
|
||||
CONFIG_DEBUG_FULLOPT=y
|
||||
CONFIG_DEBUG_SYMBOLS=y
|
||||
CONFIG_ESP32S3_OTG=y
|
||||
CONFIG_ESP32S3_UART0=y
|
||||
CONFIG_FS_PROCFS=y
|
||||
CONFIG_HAVE_CXX=y
|
||||
CONFIG_HAVE_CXXINITIALIZE=y
|
||||
CONFIG_IDLETHREAD_STACKSIZE=3072
|
||||
CONFIG_INIT_ENTRYPOINT="nsh_main"
|
||||
CONFIG_INIT_STACKSIZE=4096
|
||||
CONFIG_INTELHEX_BINARY=y
|
||||
CONFIG_NSH_ARCHINIT=y
|
||||
CONFIG_NSH_BUILTIN_APPS=y
|
||||
CONFIG_NSH_FILEIOSIZE=512
|
||||
CONFIG_NSH_LINELEN=64
|
||||
CONFIG_NSH_READLINE=y
|
||||
CONFIG_PREALLOC_TIMERS=4
|
||||
CONFIG_RAM_SIZE=114688
|
||||
CONFIG_RAM_START=0x20000000
|
||||
CONFIG_RR_INTERVAL=200
|
||||
CONFIG_SCHED_WAITPID=y
|
||||
CONFIG_START_DAY=6
|
||||
CONFIG_START_MONTH=12
|
||||
CONFIG_START_YEAR=2011
|
||||
CONFIG_SYSLOG_BUFFER=y
|
||||
CONFIG_SYSTEM_NSH=y
|
||||
52
boards/xtensa/esp32s3/esp32s3-lhcbit/include/board.h
Normal file
52
boards/xtensa/esp32s3/esp32s3-lhcbit/include/board.h
Normal file
|
|
@ -0,0 +1,52 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/include/board.h
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_INCLUDE_BOARD_H
|
||||
#define __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_INCLUDE_BOARD_H
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Clocking *****************************************************************/
|
||||
|
||||
/* The ESP32-S3 DevKit board is fitted with a 40MHz crystal */
|
||||
|
||||
#define BOARD_XTAL_FREQUENCY 40000000
|
||||
|
||||
#ifdef CONFIG_ESP32S3_DEFAULT_CPU_FREQ_MHZ
|
||||
# define BOARD_CLOCK_FREQUENCY (CONFIG_ESP32S3_DEFAULT_CPU_FREQ_MHZ * 1000000)
|
||||
#else
|
||||
# define BOARD_CLOCK_FREQUENCY 80000000
|
||||
#endif
|
||||
|
||||
/* LED definitions **********************************************************/
|
||||
|
||||
/* Define how many LEDs this board has (needed by userleds) */
|
||||
|
||||
#define BOARD_NLEDS 0
|
||||
|
||||
/* GPIO pins used by the GPIO Subsystem */
|
||||
|
||||
#define BOARD_NGPIOOUT 1 /* Amount of GPIO Output pins */
|
||||
#define BOARD_NGPIOIN 1 /* Amount of GPIO Input without Interruption */
|
||||
#define BOARD_NGPIOINT 1 /* Amount of GPIO Input w/ Interruption pins */
|
||||
|
||||
#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_INCLUDE_BOARD_H */
|
||||
116
boards/xtensa/esp32s3/esp32s3-lhcbit/include/board_memorymap.h
Normal file
116
boards/xtensa/esp32s3/esp32s3-lhcbit/include/board_memorymap.h
Normal file
|
|
@ -0,0 +1,116 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/include/board_memorymap.h
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_INCLUDE_BOARD_MEMORYMAP_H
|
||||
#define __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_INCLUDE_BOARD_MEMORYMAP_H
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <stdint.h>
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/* Kernel ROM */
|
||||
|
||||
#define KIROM_START (uintptr_t)__kirom_start
|
||||
#define KIROM_SIZE (uintptr_t)__kirom_size
|
||||
#define KDROM_START (uintptr_t)__kdrom_start
|
||||
#define KDROM_SIZE (uintptr_t)__kdrom_size
|
||||
|
||||
/* Kernel RAM */
|
||||
|
||||
#define KIRAM_START (uintptr_t)__kiram_start
|
||||
#define KIRAM_SIZE (uintptr_t)__kiram_size
|
||||
#define KIRAM_END (uintptr_t)__kiram_end
|
||||
#define KDRAM_START (uintptr_t)__kdram_start
|
||||
#define KDRAM_SIZE (uintptr_t)__kdram_size
|
||||
#define KDRAM_END (uintptr_t)__kdram_end
|
||||
|
||||
/* Exception vectors */
|
||||
|
||||
#define VECTORS_START (uintptr_t)__vectors_start
|
||||
#define VECTORS_END (uintptr_t)__vectors_end
|
||||
|
||||
/* User ROM */
|
||||
|
||||
#define UIROM_START (uintptr_t)__uirom_start
|
||||
#define UIROM_SIZE (uintptr_t)__uirom_size
|
||||
#define UIROM_END (uintptr_t)__uirom_end
|
||||
#define UDROM_START (uintptr_t)__udrom_start
|
||||
#define UDROM_SIZE (uintptr_t)__udrom_size
|
||||
#define UDROM_END (uintptr_t)__udrom_end
|
||||
|
||||
/* User RAM */
|
||||
|
||||
#define UIRAM_START (uintptr_t)__uiram_start
|
||||
#define UIRAM_SIZE (uintptr_t)__uiram_size
|
||||
#define UIRAM_END (uintptr_t)__uiram_end
|
||||
#define UDRAM_START (uintptr_t)__udram_start
|
||||
#define UDRAM_SIZE (uintptr_t)__udram_size
|
||||
#define UDRAM_END (uintptr_t)__udram_end
|
||||
|
||||
/****************************************************************************
|
||||
* Public Data
|
||||
****************************************************************************/
|
||||
|
||||
/* Kernel ROM (RX) */
|
||||
|
||||
extern uint8_t __kirom_start[];
|
||||
extern uint8_t __kirom_size[];
|
||||
extern uint8_t __kdrom_start[];
|
||||
extern uint8_t __kdrom_size[];
|
||||
|
||||
/* Kernel RAM (RW) */
|
||||
|
||||
extern uint8_t __kiram_start[];
|
||||
extern uint8_t __kiram_size[];
|
||||
extern uint8_t __kiram_end[];
|
||||
extern uint8_t __kdram_start[];
|
||||
extern uint8_t __kdram_size[];
|
||||
extern uint8_t __kdram_end[];
|
||||
|
||||
/* Exception vectors */
|
||||
|
||||
extern uint8_t __vectors_start[];
|
||||
extern uint8_t __vectors_end[];
|
||||
|
||||
/* User ROM (RX) */
|
||||
|
||||
extern uint8_t __uirom_start[];
|
||||
extern uint8_t __uirom_size[];
|
||||
extern uint8_t __uirom_end[];
|
||||
extern uint8_t __udrom_start[];
|
||||
extern uint8_t __udrom_size[];
|
||||
extern uint8_t __udrom_end[];
|
||||
|
||||
/* User RAM (RW) */
|
||||
|
||||
extern uint8_t __uiram_start[];
|
||||
extern uint8_t __uiram_size[];
|
||||
extern uint8_t __uiram_end[];
|
||||
extern uint8_t __udram_start[];
|
||||
extern uint8_t __udram_size[];
|
||||
extern uint8_t __udram_end[];
|
||||
|
||||
#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_INCLUDE_BOARD_MEMORYMAP_H */
|
||||
72
boards/xtensa/esp32s3/esp32s3-lhcbit/scripts/Make.defs
Normal file
72
boards/xtensa/esp32s3/esp32s3-lhcbit/scripts/Make.defs
Normal file
|
|
@ -0,0 +1,72 @@
|
|||
############################################################################
|
||||
# boards/xtensa/esp32s3/esp32s3-lhcbit/scripts/Make.defs
|
||||
#
|
||||
# Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
# contributor license agreements. See the NOTICE file distributed with
|
||||
# this work for additional information regarding copyright ownership. The
|
||||
# ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
# "License"); you may not use this file except in compliance with the
|
||||
# License. You may obtain a copy of the License at
|
||||
#
|
||||
# http://www.apache.org/licenses/LICENSE-2.0
|
||||
#
|
||||
# Unless required by applicable law or agreed to in writing, software
|
||||
# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
# License for the specific language governing permissions and limitations
|
||||
# under the License.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include $(TOPDIR)/.config
|
||||
include $(TOPDIR)/tools/Config.mk
|
||||
include $(TOPDIR)/tools/esp32s3/Config.mk
|
||||
include $(TOPDIR)/arch/xtensa/src/lx7/Toolchain.defs
|
||||
|
||||
ARCHSCRIPT += $(BOARD_COMMON_DIR)$(DELIM)scripts$(DELIM)esp32s3_peripherals.ld
|
||||
ARCHSCRIPT += $(BOARD_COMMON_DIR)$(DELIM)scripts$(DELIM)esp32s3_rom_aliases.ld
|
||||
|
||||
# Pick the linker scripts from the board level if they exist, if not
|
||||
# pick the common linker scripts.
|
||||
|
||||
ifeq ($(CONFIG_BUILD_PROTECTED),y)
|
||||
ARCHSCRIPT += $(call FINDSCRIPT,protected_memory.ld)
|
||||
ARCHSCRIPT += $(call FINDSCRIPT,kernel-space.ld)
|
||||
else
|
||||
ARCHSCRIPT += $(call FINDSCRIPT,flat_memory.ld)
|
||||
ifeq ($(CONFIG_ESP32S3_APP_FORMAT_MCUBOOT),y)
|
||||
ARCHSCRIPT += $(call FINDSCRIPT,mcuboot_sections.ld)
|
||||
else ifeq ($(CONFIG_ESPRESSIF_SIMPLE_BOOT),y)
|
||||
ARCHSCRIPT += $(call FINDSCRIPT,simple_boot_sections.ld)
|
||||
else
|
||||
ARCHSCRIPT += $(call FINDSCRIPT,legacy_sections.ld)
|
||||
endif
|
||||
endif
|
||||
|
||||
ifneq ($(CONFIG_DEBUG_NOOPT),y)
|
||||
ARCHOPTIMIZATION += -fno-strength-reduce
|
||||
endif
|
||||
|
||||
ARCHPICFLAGS = -fpic
|
||||
|
||||
CFLAGS := $(ARCHCFLAGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRAFLAGS)
|
||||
CPICFLAGS = $(ARCHPICFLAGS) $(CFLAGS)
|
||||
CXXFLAGS := $(ARCHCXXFLAGS) $(ARCHOPTIMIZATION) $(ARCHCPUFLAGS) $(ARCHXXINCLUDES) $(ARCHDEFINES) $(EXTRAFLAGS)
|
||||
CXXPICFLAGS = $(ARCHPICFLAGS) $(CXXFLAGS)
|
||||
CPPFLAGS := $(ARCHINCLUDES) $(ARCHDEFINES) $(EXTRAFLAGS)
|
||||
AFLAGS := $(CFLAGS) -D__ASSEMBLY__
|
||||
|
||||
# Loadable module definitions
|
||||
|
||||
CMODULEFLAGS = $(CFLAGS) -mtext-section-literals
|
||||
|
||||
LDMODULEFLAGS = -r -e module_initialize
|
||||
LDMODULEFLAGS += -T $(call CONVERT_PATH,$(TOPDIR)/libs/libc/modlib/gnu-elf.ld)
|
||||
|
||||
# ELF module definitions
|
||||
|
||||
CELFFLAGS = $(CFLAGS) -mtext-section-literals
|
||||
CXXELFFLAGS = $(CXXFLAGS) -mtext-section-literals
|
||||
|
||||
LDELFFLAGS = -r -e main
|
||||
LDELFFLAGS += -T $(call CONVERT_PATH,$(TOPDIR)/binfmt/libelf/gnu-elf.ld)
|
||||
35
boards/xtensa/esp32s3/esp32s3-lhcbit/src/Make.defs
Normal file
35
boards/xtensa/esp32s3/esp32s3-lhcbit/src/Make.defs
Normal file
|
|
@ -0,0 +1,35 @@
|
|||
############################################################################
|
||||
# boards/xtensa/esp32s3/esp32s3-lhcbit/src/Make.defs
|
||||
#
|
||||
# Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
# contributor license agreements. See the NOTICE file distributed with
|
||||
# this work for additional information regarding copyright ownership. The
|
||||
# ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
# "License"); you may not use this file except in compliance with the
|
||||
# License. You may obtain a copy of the License at
|
||||
#
|
||||
# http://www.apache.org/licenses/LICENSE-2.0
|
||||
#
|
||||
# Unless required by applicable law or agreed to in writing, software
|
||||
# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
# License for the specific language governing permissions and limitations
|
||||
# under the License.
|
||||
#
|
||||
############################################################################
|
||||
|
||||
include $(TOPDIR)/Make.defs
|
||||
|
||||
CSRCS = esp32s3_boot.c esp32s3_bringup.c
|
||||
|
||||
ifeq ($(CONFIG_BOARDCTL),y)
|
||||
CSRCS += esp32s3_appinit.c
|
||||
ifeq ($(CONFIG_BOARDCTL_RESET),y)
|
||||
CSRCS += esp32s3_reset.c
|
||||
endif
|
||||
endif
|
||||
|
||||
DEPPATH += --dep-path board
|
||||
VPATH += :board
|
||||
CFLAGS += ${INCDIR_PREFIX}$(TOPDIR)$(DELIM)arch$(DELIM)$(CONFIG_ARCH)$(DELIM)src$(DELIM)board$(DELIM)board
|
||||
|
||||
67
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3-lhcbit.h
Normal file
67
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3-lhcbit.h
Normal file
|
|
@ -0,0 +1,67 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3-lhcbit.h
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#ifndef __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_SRC_ESP32S3_LHCBIT_H
|
||||
#define __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_SRC_ESP32S3_LHCBIT_H
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
#include <nuttx/compiler.h>
|
||||
#include <stdint.h>
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Types
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Data
|
||||
****************************************************************************/
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
|
||||
/****************************************************************************
|
||||
* Public Function Prototypes
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: esp32s3_bringup
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture-specific initialization
|
||||
*
|
||||
* CONFIG_BOARD_LATE_INITIALIZE=y :
|
||||
* Called from board_late_initialize().
|
||||
*
|
||||
* CONFIG_BOARD_LATE_INITIALIZE=y && CONFIG_BOARDCTL=y :
|
||||
* Called from the NSH library via board_app_initialize()
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int esp32s3_bringup(void);
|
||||
|
||||
#endif /* __ASSEMBLY__ */
|
||||
#endif /* __BOARDS_XTENSA_ESP32S3_ESP32S3_LHCBIT_SRC_ESP32S3_LHCBIT_H */
|
||||
80
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_appinit.c
Normal file
80
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_appinit.c
Normal file
|
|
@ -0,0 +1,80 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_appinit.c
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <sys/types.h>
|
||||
#include <nuttx/board.h>
|
||||
|
||||
#include "esp32s3-lhcbit.h"
|
||||
|
||||
#ifdef CONFIG_BOARDCTL
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: board_app_initialize
|
||||
*
|
||||
* Description:
|
||||
* Perform application specific initialization. This function is never
|
||||
* called directly from application code, but only indirectly via the
|
||||
* (non-standard) boardctl() interface using the command BOARDIOC_INIT.
|
||||
*
|
||||
* Input Parameters:
|
||||
* arg - The boardctl() argument is passed to the board_app_initialize()
|
||||
* implementation without modification. The argument has no
|
||||
* meaning to NuttX; the meaning of the argument is a contract
|
||||
* between the board-specific initialization logic and the
|
||||
* matching application logic. The value could be such things as a
|
||||
* mode enumeration value, a set of DIP switch settings, a
|
||||
* pointer to configuration data read from a file or serial FLASH,
|
||||
* or whatever you would like to do with it. Every implementation
|
||||
* should accept zero/NULL as a default configuration.
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero (OK) is returned on success; a negated errno value is returned on
|
||||
* any failure to indicate the nature of the failure.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int board_app_initialize(uintptr_t arg)
|
||||
{
|
||||
#ifdef CONFIG_BOARD_LATE_INITIALIZE
|
||||
/* Board initialization already performed by board_late_initialize() */
|
||||
|
||||
return OK;
|
||||
#else
|
||||
/* Perform board-specific initialization */
|
||||
|
||||
return esp32s3_bringup();
|
||||
#endif
|
||||
}
|
||||
|
||||
#endif /* CONFIG_BOARDCTL */
|
||||
83
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_boot.c
Normal file
83
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_boot.c
Normal file
|
|
@ -0,0 +1,83 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_boot.c
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/board.h>
|
||||
#include <nuttx/mm/mm.h>
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "esp32s3-lhcbit.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Pre-processor Definitions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Private Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: esp32s3_board_initialize
|
||||
*
|
||||
* Description:
|
||||
* All ESP32-S3 boards must provide the following entry point.
|
||||
* This entry point is called early in the initialization -- after all
|
||||
* memory has been configured and mapped but before any devices have been
|
||||
* initialized.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
void esp32s3_board_initialize(void)
|
||||
{
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: board_late_initialize
|
||||
*
|
||||
* Description:
|
||||
* If CONFIG_BOARD_LATE_INITIALIZE is selected, then an additional
|
||||
* initialization call will be performed in the boot-up sequence to a
|
||||
* function called board_late_initialize(). board_late_initialize() will
|
||||
* be called immediately after up_initialize() is called and just before
|
||||
* the initial application is started. This additional initialization
|
||||
* phase may be used, for example, to initialize board-specific device
|
||||
* drivers.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
#ifdef CONFIG_BOARD_LATE_INITIALIZE
|
||||
void board_late_initialize(void)
|
||||
{
|
||||
/* Perform board-specific initialization */
|
||||
|
||||
esp32s3_bringup();
|
||||
}
|
||||
#endif
|
||||
95
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_bringup.c
Normal file
95
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_bringup.c
Normal file
|
|
@ -0,0 +1,95 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_bringup.c
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdio.h>
|
||||
#include <fcntl.h>
|
||||
#include <unistd.h>
|
||||
#include <syslog.h>
|
||||
#include <sys/stat.h>
|
||||
#include <sys/ioctl.h>
|
||||
#include <sys/types.h>
|
||||
#include <syslog.h>
|
||||
#include <debug.h>
|
||||
#include <stdio.h>
|
||||
|
||||
#include <errno.h>
|
||||
#include <nuttx/fs/fs.h>
|
||||
#include <nuttx/himem/himem.h>
|
||||
#include <arch/board/board.h>
|
||||
|
||||
#include "esp32s3-lhcbit.h"
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: esp32s3_bringup
|
||||
*
|
||||
* Description:
|
||||
* Perform architecture-specific initialization
|
||||
*
|
||||
* CONFIG_BOARD_LATE_INITIALIZE=y :
|
||||
* Called from board_late_initialize().
|
||||
*
|
||||
* CONFIG_BOARD_LATE_INITIALIZE=n && CONFIG_BOARDCTL=y :
|
||||
* Called from the NSH library
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int esp32s3_bringup(void)
|
||||
{
|
||||
int ret;
|
||||
|
||||
#ifdef CONFIG_FS_PROCFS
|
||||
/* Mount the procfs file system */
|
||||
|
||||
ret = nx_mount(NULL, "/proc", "procfs", 0, NULL);
|
||||
if (ret < 0)
|
||||
{
|
||||
syslog(LOG_ERR, "ERROR: Failed to mount procfs at /proc: %d\n", ret);
|
||||
}
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_FS_TMPFS
|
||||
/* Mount the tmpfs file system */
|
||||
|
||||
ret = nx_mount(NULL, CONFIG_LIBC_TMPDIR, "tmpfs", 0, NULL);
|
||||
if (ret < 0)
|
||||
{
|
||||
syslog(LOG_ERR, "ERROR: Failed to mount tmpfs at %s: %d\n",
|
||||
CONFIG_LIBC_TMPDIR, ret);
|
||||
}
|
||||
#endif
|
||||
|
||||
/* If we got here then perhaps not all initialization was successful, but
|
||||
* at least enough succeeded to bring-up NSH with perhaps reduced
|
||||
* capabilities.
|
||||
*/
|
||||
|
||||
UNUSED(ret);
|
||||
return OK;
|
||||
}
|
||||
85
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_reset.c
Normal file
85
boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_reset.c
Normal file
|
|
@ -0,0 +1,85 @@
|
|||
/****************************************************************************
|
||||
* boards/xtensa/esp32s3/esp32s3-lhcbit/src/esp32s3_reset.c
|
||||
*
|
||||
* Licensed to the Apache Software Foundation (ASF) under one or more
|
||||
* contributor license agreements. See the NOTICE file distributed with
|
||||
* this work for additional information regarding copyright ownership. The
|
||||
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
||||
* "License"); you may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at
|
||||
*
|
||||
* http://www.apache.org/licenses/LICENSE-2.0
|
||||
*
|
||||
* Unless required by applicable law or agreed to in writing, software
|
||||
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
||||
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
||||
* License for the specific language governing permissions and limitations
|
||||
* under the License.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <stdlib.h>
|
||||
#include <debug.h>
|
||||
#include <assert.h>
|
||||
#include <nuttx/arch.h>
|
||||
#include <nuttx/board.h>
|
||||
|
||||
#include "esp32s3_systemreset.h"
|
||||
|
||||
#ifdef CONFIG_BOARDCTL_RESET
|
||||
|
||||
#if CONFIG_BOARD_ASSERT_RESET_VALUE == EXIT_SUCCESS
|
||||
# error "CONFIG_BOARD_ASSERT_RESET_VALUE must not be equal to EXIT_SUCCESS"
|
||||
#endif
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: board_reset
|
||||
*
|
||||
* Description:
|
||||
* Reset board. Support for this function is required by board-level
|
||||
* logic if CONFIG_BOARDCTL_RESET is selected.
|
||||
*
|
||||
* Input Parameters:
|
||||
* status - Status information provided with the reset event. This
|
||||
* meaning of this status information is board-specific. If not
|
||||
* used by a board, the value zero may be provided in calls to
|
||||
* board_reset().
|
||||
*
|
||||
* Returned Value:
|
||||
* If this function returns, then it was not possible to power-off the
|
||||
* board due to some constraints. The return value in this case is a
|
||||
* board-specific reason for the failure to shutdown.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int board_reset(int status)
|
||||
{
|
||||
syslog(LOG_INFO, "reboot status=%d\n", status);
|
||||
|
||||
switch (status)
|
||||
{
|
||||
case EXIT_SUCCESS:
|
||||
up_shutdown_handler();
|
||||
break;
|
||||
case CONFIG_BOARD_ASSERT_RESET_VALUE:
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
|
||||
up_systemreset();
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#endif /* CONFIG_BOARDCTL_RESET */
|
||||
Loading…
Reference in a new issue