Modify the kernel to use only atomic_xx and atomic64_xx interfaces,
avoiding the use of sizeof or typeof to determine the type of
atomic operations, thereby simplifying the kernel's atomic
interface operations.
Signed-off-by: zhangyuan29 <zhangyuan29@xiaomi.com>
change bt_driver_register/unregister function name to
bt_driver_set/unset, which would be prepared for bt_driver.h
Signed-off-by: chengkai <chengkai@xiaomi.com>
Most tools used for compliance and SBOM generation use SPDX identifiers
This change brings us a step closer to an easy SBOM generation.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
By enabling the config `CONFIG_BLUETOOTH_TXCMD_PINNED_TO_CORE` and
setting the value of `CONFIG_BLUETOOTH_TXCMD_CORE`, it's possible
to pin the HCI TX thread to a specific core on a SMP-enabled setup.
This is necessary for devices that require that the function that
sends data (`bt_send`) to be called from a specific core.
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
This bluetooth stack remains in an inconsistent state when
the bluetooth HCI module is removed. This change adds a
bt_netdev_unregister function that can be used to clean up
after a module is removed. Some global variables are also
set to their default values.
In the past, header file paths were generated by the incdir command
Now they are generated by concatenating environment variables
In this way, when executing makefile, no shell command will be executed,
it will improve the speed of executing makfile
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
since it is impossible to track producer and consumer
correctly if TCP/IP stack pass IOB directly to netdev
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
This was broken since 6c69b12000.
The first byte in io_data buffer must be the BT H4 packet type.
Without this change an assertion in bt_netdev.c:535 is always raised and nimble host layer crash.
Those files are ported from the Intel/Zephyr
arduino101_firmware_source-v1.tar package
where the code was released with a compatible 3-clause BSD license
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
If ALLOW_BSD_COMPONENTS is not enabled in the license setup,
Bluetooth LE support will be disabled
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
