1. pm configuration demonstrates the use of power management present on the ESP32-S3.
2. You can use the pmconfig command to test the power management, for details look at
``Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst``
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
The Simple Boot feature for Espressif chips is a method of booting
that doesn't depend on a 2nd stage bootloader. Its not the
intention to replace a 2nd stage bootloader such as MCUboot and
ESP-IDF bootloader, but to have a minimal and straight-forward way
of booting, and also simplify the building.
This commit also removes deprecated code and makes this bootloader
configuration as default for esp32s3 targets and removes the need
for running 'make bootloader' command for it.
Other related fix, but not directly to Simple Boot:
- Instrumentation is required to run from IRAM to support it during
initialization. `is_eco0` function also needs to run from IRAM.
- `rtc.data` section placement was fixed.
- Provide arch-defined interfaces for efuses, in order to decouple
board config level from arch-defined values.
Signed-off-by: Almir Okato <almir.okato@espressif.com>
This commit implements the common RMT driver (already available for
the other Espressif's xtensa-based devices) for ESP32.
This allows us to have a proper separation between the lower and
upper-half drivers and use the 'ws2812' example to drive WS2812 RGB
LEDs.
This commit updates the Wi-Fi and the BLE driver of ESP32. Most of
the changes rely on using the common sources and header files for
xtensa-based Espressif's SoCs.
The new Wi-Fi driver supports WPA3-SAE for both Station and SoftAP
mode. BLE's coexistence mode was enhanced according to the latest
libraries.
Please note that other sources required minor changes in order to
be compatible with the common sources.
This driver is used with QEMU, to make it possible
to use networking.
This is not the MAC in ESP32, however, it can be used with QEMU.
The code was shamelessly copied from 31dac92e5f
The board's microphone uses 24-bit i2s and this commit also fixes
the segmentation fault caused by the audio buffer overflow.
arch/xtensa/src/esp32/esp32_i2s.c: Fix bug regarding 24-bit audio and add AUDIOIOC_STOP to ioctl
drivers/audio/audio_i2s.c: Report number of channels on AUDIOIOC_GETCAPS
in boards/xtensa/esp32/esp32-sparrow-kit:
/configs/nsh/defconfig: Add I2S configs
/src/esp32-sparrow-kit.h: Add the signature of esp32_i2sdev_initialize()
/src/esp32_bringup.c: Add call to esp32_i2sdev_initialize()
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Enable with ./tools/configure.sh -l esp32-devkitc:dac
DAC channel 0 = GPIO 25
DAC channel 1 = GPIO 26
default path: /dev/dac0
Resolution 8 bits = values 0~255
Voltage: 0~Vref
The reference voltage 'Vref' here is input from the pin VDD3P3_RTC
which ideally equals to the power supply VDD (3.3V).
- A pre-built IDF bootloader is used by default;
- `ESP32S3_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S3_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32S2_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32S2_PARTITION_TABLE.
- A pre-built IDF bootloader is used by default;
- `ESP32_PARTITION_TABLE` requires the IDF bootloader to be built
from sources.
- Native MCUboot also can be used to boot the device. It will be
built from sources and depends on !ESP32_PARTITION_TABLE.
By integrating the Espressif`s HAL repository into the current
ESP32-S2 implementation on NuttX, it is possible to call functions
that makes it easier to setup the registers of the ESP32-S2,
enabling the usage of common Espressif drivers.
By integrating the Espressif`s HAL repository into the current
ESP32-S3 implementation on NuttX, it is possible to call functions
that make it easier to set up the registers of the ESP32-S3 and
enables the usage of common Espressif drivers. Please note that
Espressif's HAL repository was already being used for the Wi-Fi
driver. Then, this commit includes other source files to be used
by other drivers other than Wi-Fi and reorganize the build process.
The RMT (Remote Control) character driver allows to use the RMT
peripheral (usually, a one-wire peripheral dedicated to driving
IR remote control) as a character driver.
Please note that this perpiheral depends on the lower-half specific
driver implementation.
Once these messages are thrown during the system's bring-up, it is
advisable them to be output by the syslog considering the file
system initialization.
The SmartFS partition needs to be formatted before being mounted.
Otherwise, it would throw an error message. The error message now
contains a suggestion to format the partition when such an error
is detected.
1. Configurable mapping of virtual address to psram physical address
2. Access SPIRAM memory at high physical address through bank switching
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
1. If CONFIG_ESP32S3_PHY_INIT_DATA_IN_PARTITION and CONFIG_ESP32S3_SUPPORT_MULTIPLE_PHY_INIT_DATA are enabled,
PHY initialization data (PHY initialization data is used for RF calibration) will be loaded from a partition.
2. The corresponding PHY init data type can be automatically switched according to the country code,
China's PHY init data bin is used by default, country code can be modified through the wapi command: wapi country <ifname> <country code>.
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
This commit sets the BLE's interrupt as a IRAM-enabled interrupt,
which enables it to run during a SPI flash operation. This enables
us to create a cache to off-load semaphores and message queues
operations and treat them when the SPI flash operation is finished.
By doing that, we avoid packet losses during a SPI flash operation.
This commit provides an interface to register ISRs that run from
IRAM and keeps track of the non-IRAM interrupts. It enables, for
instance, to avoid disabling all the interrupts during a SPI flash
operation: IRAM-enabled ISRs are, then, able to run during these
operations.
It also makes the code look more similar to the ESP32-S3 SPI flash
implementation by creating a common `esp32_spiflash_init` that is
responsible to create the SPI flash operation tasks. The function
intended to initialize the SPI flash partions was, then, renamed to
`board_spiflash_init`.
During PSRAM initialization and flash operations, the Cache needs to be disabled.
So all data and code for the aforementioned scope is required to be placed in Internal RAM.
After https://github.com/apache/nuttx/pull/11007/ was merged, the
path for some files changed, requiring the linker to be fixed to
make it run from the internal memory once again.
Using up_textheap_memalign to allocate memory if arch support textheap
for loading section.
The default system heap does not support execution permissions,
so up_textheap_memalign allocation is required.
this patch can fix issue about #11043
update esp32 elf config:
remove -CONFIG_ARCH_USE_TEXT_HEAP=y becuase ARCH_CHIP_ESP32 select
ARCH_HAVE_TEXT_HEAP
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
- migrated /README are removed from /boards
- there are a lot of READMEs that should be further converted to rst.
At the moment they are moved to Documentation/platforms and included in rst files
This commit sets the BLE's interrupt as a IRAM-enabled interrupt,
which enables it to run during a SPI flash operation. This enables
us to create a cache to off-load semaphores and message queues
operations and treat them when the SPI flash operation is finished.
By doing that, we avoid packet losses during a SPI flash operation.
This commit provides an interface to register ISRs that run from
IRAM and keeps track of the non-IRAM interrupts. It enables, for
instance, to avoid disabling all the interrupts during a SPI flash
operation: IRAM-enabled ISRs are, then, able to run during these
operations.
The board-level GPIO support is different from the already existing
button and LEDC support because it enable us to register the GPIO
pins as devices in `/dev/gpioX`. Some applications are able to use
this interface to read and write the GPIO pins.
Documentation was added regarding its usage. Please check
`Documentation/platforms/xtensa/esp32s3/boards/esp32s3-devkit/index.rst`
Provide initial support for audio through the I2S peripheral to the
CS4344 audio codec on ESP32-S3-DevKitC-1 board.
Please check documentation for usage examples.
ESP32-S3 has only one 2.4 GHz ISM band RF module, which is shared
by Bluetooth and Wi-Fi, so Bluetooth can’t receive or transmit data
while Wi-Fi is receiving or transmitting data and vice versa.
Under such circumstances, ESP32-S3 uses the time-division
multiplexing method to receive and transmit packets.
- Added Wi-Fi related symbols to the kernel-space linker;
- Allocate more RAM to the kernel (to be useb by the Wi-Fi driver).
- Create a specific defconfig.
Instead of setting kernel/user space instruction and data ROM as
hard-coded values on linker, set them according to the max size
of the kernel image set by CONFIG_ESP32S3_KERNEL_IMAGE_SIZE. This
is done by making KIROM, UIROM, KDROM and UDROM dependent on the
kernel size value. Also, override CONFIG_NUTTX_USERSPACE config
according to CONFIG_ESP32S3_KERNEL_IMAGE_SIZE by using a custom
PREBUILD definition.
drivers/sensors/bme680.c: The bme680 driver
sensor.h: Added new type of sensor (Gas) to be used for retrieving the bme680 data
esp32/common/src/esp32_bme680.c: bme680 support on esp32
esp32/esp32-sparrow_kit/esp32_bringup.c: added support for the bme680
esp32/esp32-sparrow-kit/configs/nsh/defconfig: fixed defconfig ci problem
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
esp32-sparrow-kit: Fixed defconfig
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Code is now C89 compatible
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Reused already defined sensor data structs by registering every sub-sensor separately
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Implemented suggestions
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
board/esp32s3/common is for common board driver. It should not
include a header file from specific board. so remove include
of esp32s3-devkit.h from some of the common driver source
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
esp32-sparrow-kit: Added rgb led driver to bringup and to defconfig
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Fixed checkstyle
Signed-off-by: simonatoaca <simona.alexandra2000@gmail.com>
Update esp32_rgbled.h
Update boards/xtensa/esp32/common/src/esp32_rgbled.c
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Update boards/xtensa/esp32/common/src/esp32_rgbled.c
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Update boards/xtensa/esp32/common/src/esp32_rgbled.c
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Update boards/xtensa/esp32/common/src/esp32_rgbled.c
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Removed ret 0 as an error in the case of nx_write()
The framebuffer itself already initializes the display so there is no need to
do the reverse operation. Otherwise the code gets stuck in an infinite loop.
Signed-off-by: Robert-Ionut Alexa <robertalexa2000@gmail.com>
Whenever a SPI flash operation is going to take place, it's
necessary to disable both the instruction and data cache. In order
to avoid the other CPU (if SMP is enabled) to retrieve data from
the SPI flash, it needs to be paused until the current SPI flash
operation finishes. All the code that "pauses" the other CPU (in
fact, the CPU spins until `up_cpu_resume` is called) needs to run
from the instruction RAM.
This config also prevents crashes due to the commit 6be363f, which
fix a race condition in multi-threaded write/read of the serial
driver, but increases stack size.
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
Instead of using Espressif's emulated NVS to save Wi-Fi data, use
`wapi`s wireless configure initialization mechanism for saving
Wi-Fi data. It 1) avoids creating a specific storage partition
just to save Wi-Fi data (ESP32-S3's storage partition is used
instead); 2) avoids initialization problems of the emulated NVS
when SMP is enabled (the Wi-Fi driver tries to initialize it before
the actual partition is initialized); and 3) enables reconnecting
using `wapi reconnect` command and connect the device automatically
on bringup if `CONFIG_NETUTILS_NETINIT` is selected.
This commit aims to enable the use of ROM functions on ESP32-S2.
This is done by creating the required syscall stubs table and adding the missing symbols to the linker script.
This commit aims to enable the use of ROM functions on ESP32.
This is done by creating the required syscall stubs table and adding the missing symbols to the linker script.
